Series 4WP2 and 4WP2T
WORM GEAR POWER WINCHES
Model 4WP2
Up to 2000 lb capacity
Machine Cut Worm Gears provide accurate operation    and long lasting service.
Enclosed Oil Bath provides continuous lubrication of    gears to minimize wear. Oil seals keep oil in and dirt out.
				Model 4WP2T
115 Volt Single Phase Electric Motor includes power    cord with grounded plug and a momentary contact-type    push button pendant control on a control cord.
			Mounting Options include floor, wall, or ceiling.
			Wire Rope Assemblies sold separately. (see bottom page)
Internal Mechanical Brake provides positive load    control for lifting and lowering operations.
			Cast Aluminum construction, for lightweight strength.
			Corrosion Resistant durable paint finish protects against    corrosion in harsh environments.
Ball Bearings and self-aligning bronze bearings provide    smooth and efficient operation.
			Large Diameter Drums minimize wear to the wire rope    and help extend its life.
Pressure Plate on series 4WP2T8 only, applies pressure    to drum and wire rope to help maintain uniform winding.
			Clutch Model allows operator to manually disengage the    drum to rapidly unwind wire rope. Clutch models do not    included pressure plates.
Dual Function Cable Anchor for quick disconnect of    wire rope with swagged ball fitting, or recessed cable    anchor with set screw for wire rope with unfinished end.

OPTIONS AND ACCESSORIES
		DIMENSIONS
Emergency Hand Crank for manual    operation in case of power failure.    Does not include handle. Available    for Series 4WP2 and 4WP2T8 only.
Two Part Line Kit to convert to    double line rigging. Available for    Series 4WP2T8 only.
Rotary Limit Switches for    secondary shutoff to limit load travel    in one or two directions. Not    available on clutch models.
Special Motors and Controls    including severe duty and explosion    proof.
Special Finishes for hazardous    environments.
Torque Limiters as part of the motor    controls on electric models.
Important: It is the owner's or operator's responsibility to determine the suitability of the equipment to its intended use. Study all applicable codes, manuals, and regulations. Be sure to read the Owner's Manual supplied with the equipment before operating it.

SERIES 4WP2 & 4WP2T - DRUM DIMENSIONS
Model extension Drum dia. Flange dia. Drum width Fleet angle distance² 4WP2 2.50 in 5.00 in 5.00 in 8.0 ft 4WP2T8-2000-8 2.50 in 7.00 in 8.00 in 12.75 ft 4WP2TC-2000-8 2.50 in 7.00 in 5.50 in 8.75 ft
² Recommended minimum distance between drum and lead sheave for smooth drum.
Dimensions are for reference only and subject to change without notice.

ELECTRIC MOTOR CONTROLS
			Single Speed Reversing Magnetic Controls for 1 and 3 phase motors up to 40 hp
			UL, IEC, or CSA Recognized components throughout.
			Steel Enclosure NEMA 4 rated (watertight) keeps dirt and water out.   Approved for most outdoor applications.
			Pendant Control Switch NEMA 4X rated (watertight), on 50 foot    cord, allows operator to stand away from winch during operation.    Pendant control is operated with momentary contact-type push buttons.   Cord lengths of less than 50 feet are available, please specify when   ordering.
			Reversing Contactor is electrically and mechanically interlocked to    deliver smooth reversing control.
When ordering please include the following: voltage and phase required, motor horsepower, pendant control cord length - up to 50 ft., and pendant control labeling - For/Rev or Up/Down.
			Thermal Overload Relay trips power OFF to protect motor from    overheating. Switch is manually reset.
			Fused Control Circuit powers pendant with 115 volt, 2 amp current    to help protect against high voltage shocks.
OPTIONS			Wiring Diagram is supplied inside enclosure.
			Steel Mounting Bracket secures control box to winch.
Special current or horsepower ratings, special rated enclosures for explosive or harsh environments, soft start or soft stop controls, variable speed or multispeed controls, torque limiting controls, selector switches, power cord disconnects, and various panel mounted controls or pilot lights.
			Variable Frequency Drives
			Variable frequency drive controls are available to provide accurate    positioning of loads, soft starts and soft stops, and overload protection.
			For 3 phase 230 VAC and 460 VAC motors from 1 to 5 hp.
			For 3 phase 230 VAC motors from 1 to 30 hp.
			For 3 phase 460 VAC motors from 1 to 60 hp.

WIRE ROPE
		How to Order Wire Rope
		The breaking strength of new wire rope should be 5 times the size of the largest load for lifting applications, and 3 times the size of the largest load for pulling applications. Contact a reputable wire rope supplier for more information.

Back to Product Page