LKG LK Goodwin Co. Material Handling Equipment Toll Free: 1-800-343-2478
HOME ORDER SEARCH QUOTE CONTACT US ABOUT US MY ACCOUNT SHOPPING CART
 
Product Index
 
Back to Product Page
ALUMINUM STAIRS WITH HORIZONTAL
PLATFORM EXTENSIONS
Reach, cross, or access any area
with Stor Deck custom fit stair
designs. Sketched below are just
a few of the possible configura-
tions which can be created to
provide the path necessary to
solve your personnel access or
production requirements. Now
you can use any of our standard
stair designs in combination with
our horizontal stair extensions to
form the walkway most suited to
your building or manufacturing
process. The sketches below are
just a few examples of the limit-
less possible configurations.
• Provides safe walkways over conveyors, pipes and
   other obstacles.
• Choose 36" or 48" tread width - special sizes
   available upon request.
• Overall width = tread width + 4".
• Quality engineered to your specific height requirements
• Designed for safety and convenience
• Heavy duty bar grating or diamond plate stair treads
   won’t sag or dish (standard).
• Factory welded aluminum handrails of 1 1/2" x .125
   square tubing.
• 2 rail system with toeguard (standard).
• 10" structural channel stringers.
• Structural connections are made with 5/8" stainless
   steel dia. bolts and 3/8" butt plates.
• Fire proof construction.
• Meets OSHA requirements. See OSHA standard
   1910.25 (Fixed Industrial Stairs) listed below price
   table.
• Standard finish is mill finish aluminum.
Two OSHA stairs used with a horizontal extension to
form a heavy duty crossover bridge.

OSHA
Nominal 45 degree stair angle
BOCA
Nominal 7/11-rise/run 32 degree
stair angle
Ships Ladder
Nominal 68 degree
ladder angle

Aluminum Stair Treads
I Bar grating stair treads with corrigated aluminum nosing are safe, self-cleaning,
skid-resistant and economical.
CHOOSE FROM MANY DIFFERENT COMBINATIONS
(SEE BELOW FOR SOME EXAMPLES)
OSHA DESIGN
BOCA DESIGN
SHIPS LADDER DESIGN
3 RAILS
OSHA - WALKWAY -
OSHA
BOCA 2 RAILS - WALKWAY -
SHIPS LADDER
OSHA - WALKWAY -
SHIPS LADDER
OSHA - WALKWAY -
SHIPS LADDER
SHIPS LADDER - WALKWAY -
BOCA 3 RAILS
SHIPS LADDER - WALKWAY -
SHIPS LADDER
CUSTOM SIZES - SAME DAY QUOTES
Custom sizes and configurations are readily available. We provide same day price quotes if you require a special
stair angle, specific tread rise/run, or a maximum horizontal stair run to satisfy available floor space constraints.

FACTORY LOAD TEST
In addition to theoretical
design analysis
FS Industries has
performed actual load
tests with a 25%
overload to insure
design conformance to
OSHA standard 1910.25
which is printed below
test photos.
1250 lbs. concentrated load applied
to the center span of stair tread on a
3" long x 1 1/2" flat bar bearing surface.
Underside view of 1250 lbs.
Concentrated load suspended
from center of stair tread.
1250 lbs. load on the center of
the crossover span.
1250 lbs. Load applied to the center
of the horizontal crossover section.
1250 lbs. Load applied to the bolted
structural connection point of the stair
and the horizontal crossover section.
OSHA STANDARD 1910.25 STAIRWAYS
Walking-Working Surfaces and Personal Fall Protection Systems Final Rule
Frequently Asked Questions
The intent of OSHA’s Walking-Working Surfaces standard, 29 CFR Part 1910, Subpart D & I, is to increase the
protection of general industry employees and employers from hazards associated with walking-working surfaces. The
rule making will significantly reduce the number of worker deaths and injuries that occur each year resulting from
workplace slip, trip, and fall hazards. The final rule was published on November 18, 2016, and became effective on
January 17, 2017. Some requirements in the final rule have compliance dates after the effective date and will be
discussed in further detail below. This final rule and the associated preamble, providing more detailed explanation of
the rule, is available on the Federal Register website at 81 FR 82494, Walking-Working Surfaces; Personal Protective
Equipment; Final Rule, November 18, 2016.
OSHA requirements are set by statute, standards, and regulations. The Agency’s interpretations explain these require-
ments and how they apply to particular circumstances, but they do not create additional employer obligations. Note
that our enforcement guidance may be affected by legislative or rule making changes to OSHA requirements. Also,
from time to time we update our guidance in response to new information. To keep apprised of such developments,
you can consult OSHA’s website at http://www.osha.gov.
This webpage provides guidance, in a question and answer format, regarding OSHA’s Final Rule, Walking-Working
Surfaces and Personal Protective Equipment, 29 CFR Part 1910, Subpart D and I. These Frequently Asked Questions
(FAQs) are divided into five sections: general questions, rope descent system (RDS) questions, outdoor advertising
questions, residential roof questions, and agricultural operation questions.
Standard Stairs
Does the exception to the 9.5-inch riser height and 9.5-inch tread depth requirements for stairs installed before
January 17, 2017 (§19210.25(c)(5)), also apply to stairs designed and fabricated, but not yet installed, by that date?
Stairs with design drawings issued for construction or that were in fabrication before January 17, 2017, but not
installed, will be in compliance if they met the previous requirements for standard stairs.
Under the previous standard, stairs with a handrail that doubles as a stair rail could have a rail height of 30 to 34
inches. If an employer's stairs were installed prior to January 17, 2017, must the rails have a minimum height of
36 inches if the stair rail doubles as a handrail?
The final rule does not affect stair rail systems and handrails installed before January 17, 2017 that were in com-
pliance with the requirements in the old standard.
Does the requirement that standard stairs have a slope between 30 to 50 degrees apply to stairs installed after January
7, 2017. Therefore, the maximum angle for standard stairs is 45 degrees.
Yes. The final rule limits the maximum rise height and minimum tread depth to 9.5 inches for standard stairs installed
after January 17, 2017. Therefore, the maximum angle for standard stairs is 45 degrees.
Are stairs installed after January 17, 2017, that have an angle of 50 degrees considered to be ships stairs?
The final rule defines ship stairs as “a stairway that is equipped with treads, stair rails, and open risers, and has a slope
of 50 to 70 degrees.” Ship stairs must also comply with §1910.25(b) and (e), such as a minimum tread depth of 4
inches, a minimum tread width of 18 inches, and a vertical clearance above any stair tread to any overhead
obstruction of at least 6 feet 8 inches.
What if the doorway described in §1910.25(b)(5)(ii) and shown in figure D-7 is perpendicular to the direction of
travel and opens onto the landing? Does the same dimension apply to this condition?
Yes. As figure D-7 illustrates, Section 1910.25(b)(5) requires that a platform be provided when a door or a gate opens
directly onto a stairway. For platforms installed after January 17, 2017, the final rule also requires that employers
ensure the swing of the door or gate does not reduce the "effective usable depth" of the platform to less than 22 inches (§1910.25(b)(5)(ii)). The preamble to the final rule describes “effective usable depth” as the portion of the platform
beyond the swing of the door where a worker can stand when opening the door (82 FR 82557). The provision applies
equally to stairway doors that are perpendicular to the direction of travel.
Are fixed stairs attached to the exterior of tanks required to comply with the requirements of §1910.25(b) or would
those stairs fall under the exemptions in §1910.25(a)?

The exception from the stair requirements in §1910.25(a) only applies to stairs serving floating roof tanks, stairs on
scaffolds, stairs on self-propelled motorized equipment, or stairs designed into machines or equipment. For stairs on
the exterior of other tanks, employers would have to ensure they comply with the requirements in §1910.25(b) and (c).
Would winding stairs attached to tanks be required to meet the requirements in §1910.25(d) for spiral stairs?
No. Section 1910.21(b) defines spiral stairs as a "series of treads attached to a vertical pole in a winding fashion,
usually within a cylindrical space" (emphasis added). Winding stairs attached to tanks do not have vertical poles;
therefore, they are not spiral stairs and must meet the requirements of §1910.25(b) and (c).
Based on the height requirements for stair rails and handrails and the requirements in Table D-2, are both stair rails
and handrails required on stairs that have two open sides and are less than 44-in. wide?

Yes. Section 1910.28(b)(11)(ii) Table D-2 contains a printing error, which OSHA will correct in a published notice.
For each flight of stairs with two open sides and a width of less than 44 inches, column 4 of Table D-2 should state
"One stair rail system with hand rail on each open side" is required. (See 81 FR 82611-12).
Aluminum Stairs With Horizontal Platform Extensions, Aluminum Stairs, Stairs, Industrial Stairs, Metal Stairs, Open Tread Stair, OSHA Prefab Stairways, Outdoor Steel Stairs, Prefab Metal Stairs, Prefab Steel Stairs, Prefabricated Stair, Stair Manufacturers, Steel Pan Stairs, and Steel Stairs from your complete source for material.
handling equipment.

Back to Product Page

HOME / ORDER / SEARCH / QUOTE / CONTACT US / ABOUT US / MY ACCOUNT/ SHOPPING CART