Back to Product Page
CONCRETE
ROUND 4 SEAT TABLE
|
|
|
|
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~
Add items to your online shopping cart ~
Click the Model No. of the item
you wish to purchase.
|
|
|
|
|
Simple
lines and colors make these tables an
excellent choice for an outdoor café or park
area. High quality, low maintenance. |
|
|
|
|
|
Accepts
optional umbrella without extra stand.
New and improved for easier assembly.
Supersedes TF3125. Also available in two
seat and three seat models. ALSO--
REFINISHING KIT: TF3315 Make your
table look NEW!! All the materials you need
to refinish your concrete tables, benches, and
seats to restore them to like new condition. |
|
|
|
|
|
|
|
|
|
|
|
Size:
66" Dia. x 30" H installed.
Weight: 1100 lbs.
Seating Capacity: 8 persons.
Material: Reinforced concrete.
Colors: See Options.
Reinforcing: 1/4 & 3/8" Dia. steel rebar.
Hardware: (1)- table-to-leg bracket. |
|
|
(8)-
seat-to-leg brackets.
(8) - 3/8" Dia. x 5 1/2" hex screws.
(16) - 3/8 x 7/8 O.D. Flatwashers
(8) - 3/8" locking hex nuts.
(4) - Neoprene Pads.
(24) - 3/8" Dia. x 1-1/4" hex flange
screws.
(1) - 1/8 x 3 Keeper Pin. |
|
|
|
|
|
|
|
|
|
PRICE:
$1,900.00
|
|
|
|
|
|
|
|
|
|
|
Table
Refinishing Kit: TF3315
$198.50 |
|
|
|
|
|
|
|
|
|
|
This
Quick Ship table is available in 2 colors -
Standard Ground & Polish top and bench with Acid Wash legs
in Sand or Gray. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frame
(legs): (1) - top interlocking leg.
(1)
- bottom interlocking leg. |
|
|
Assembly:
Do not over tighten bolts or inserts
will pull out. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maintenance:
Periodically rinse with water
and mild detergent. Reseal annually. |
|
Top:
(1) - 38" Dia. x 2".
Benches: (4) - benches 34" L x 12" W x 2"
H. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Packaging:
Packaged unassembled in
crate, and shrink wrapped in plastic. |
|
Optional
Anchoring: (4) - 3/8" x 1-1/2"
inserts (angle brackets not provided). |
|
|
|
|
|
|
|
|
|
|
|
Standard:
(1) - 1-9/16" Dia. x 2" pop-out plug
in table top for umbrella pole. |
|
|
|
|
|
|
|
Available
Colors
|
|
|
|
Refinishing
Ground & Polished Concrete Instructions
|
|
|
|
|
|
|
|
Kit
Includes: |
|
|
|
|
|
-
2 lbs Grout Mixture
- 10 oz Bonding Agent
- 4 Spray Cans of Sealer |
|
|
|
|
|
|
|
|
|
Additional
Items Needed: |
|
|
|
-
Rubber Gloves
- #240 Sand Paper
- Sanding Block
- Mixing Tool
- Scrubbing Pad |
-
#80 Grit Sand Paper
- Pail
- Sponge
- Squeegee |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note:
Wear rubber gloves during entire refinishing process. Refinishing
results are best
when all excess grout is removed and surface is sanded smooth.
Check for and clean up
spills after each step. Newly refinished tables will retain
an attractive appearance for
several years if they are resealed at least once a year. |
|
|
|
|
|
|
|
1.
Scrub and Rinse
Rinse surface with water while using scrubbing pad to
remove dirt and grime. Using the sanding block and
#80 sand paper, sand surface. Repeat rinse. |
|
2.
Grout
Mix grout and bonding agent together to create
a creamy consistency in a pail. Allow to set for
5 minutes Apply to the surface using a circular
motion, with a sponge to fill all voids. Can
be used on smooth edges, not on acid wash
surfaces. |
|
|
|
|
|
|
Note:
Acid wash edges to be taped off before groutin
the surface to avoid getting grout in pores of edge. |
|
|
|
|
|
3.
Remove Excess Grout
Immediately remove all excess grout with a squeegee.
Apply water as needed to keep grout moist with a spray
bottle. Thoroughly inspect the surface to be certain it is
clean. Allow to cure for approximately 24 hours. |
4.
Wet-Sand
Once the surface has cured, wet-sand grouted
surface using sanding block, #240 sandpaper
and water. |
|
|
|
|
|
|
|
|
|
5.
Clean
Thoroughly rinse with water and allow to dry. Surface
must be dust free. If tape was needed for edges
remove tape before cleaning the surface. |
|
4.
Wet-Sand
Once the surface has cured, wet-sand grouted
surface using sanding block, #240 sandpaper
and water. |
|
|
SPECIFICATION
|
|
|
|
|
|
1.1
SUMMARY
A. Section includes: Furnish Precast Concrete Table
indicated on drawings
or specified herein. |
|
1.2
REFERENCES
A. American Society for Testing & Materials
1. ASTM C33 2. ASTM C150
3. ASTM C31 |
|
1.5
SUBMITTALS
A. Submit product data, shop drawings and Samples.
1. Product Data: Manufacturer's
specifications and
technical
data edited specifically for proposed
system,
including the following specific information:
a. Detailed
specification of construction fabrication.
b. Manufacturer's
installation instructions
c. Maintenance
literature
d. Product
warranty
2. Shop Drawings: Indicate
pertinent dimensions,
general construction,
component connections
anchoring
methods, hardware and installation
procedures.
3. Samples as requested
by Architect. |
|
1.6
QUALITY ASSURANCE
A. Qualifications of Manufacturer: Manufacturer
to be
pre-qualified by specifier
prior to bidding. Failure to
comply will result in disqualification
of bid. Manufacturer
to have at least five years
experience in the manufacturer
of precast concrete tables
field proven for at least five
years. |
|
|
|
|
|
1.10
WARRANTY
Manufacturer shall submit a written warranty
for
precast products for the period of two
years upon
acceptance of products. |
|
2.2
MATERIALS
A. Portland Cement: ASTM C150 specifications for
Portland Cement.
B. Aggregates: All aggregates to meet ASTM C33
specifications, to be cleaned
of foreign matter and
properly graded to size.
C. Coloring: Pigments used shall be inorganic, resistant
to alkalinity and used
as per manufacturers
recommendations. |
|
|
|
|
Concrete Round
Table, Concrete Tables, Park Furnishings, Tables, Concrete
and Steel Tables, Plastic Picnic Table,
Polysteel Tables, Site Amenities, Site Furnishings, Steel
Tables, and Street Furniture from your source for material
handling equipment.
|
Back to Product Page
|
HOME /
ORDER / SEARCH
/
QUOTE /
CONTACT US / ABOUT
US /
MY ACCOUNT/
SHOPPING CART |
|