LOAD
HUGGER CARGO CONTROL
|
RATCHET
ASSEMBLIES - SERIES 1,000
|
|
|
|
Type
B Assemblies |
|
|
|
|
|
Two-piece
assemblies with one piece attached to the ratchet, and the other
end is adjustable. Numerous end
fittings are available to handle any requirements. (See below) |
|
|
|
1" wide polyester webbing |
|
Ultimate strength - 2,100 lbs. * |
|
Working Load Limit - 700 lbs. * |
|
|
|
|
|
|
|
|
*
When using flat hooks in Series 1,000, ultimate strength is
1,000 lbs., Working load limit is 330 lbs.
** When using chain anchor fittings, fixed end length is 24". |
|
|
|
|
Load
Hugger BASICS
|
|
|
|
|
Load Hugger cargo control and load securement products offer
the van and flatbed operator a wide variety of options
to meet U.S. DOT, FMCSA (Federal Motor Carrier Safety Administration),
and CVSA (Commercial Vehicle Safety
Alliance) requirements.* |
|
|
|
|
Features
and Benefits |
|
Environmental
Considerations |
|
|
|
|
Meets all U.S. DOT, FMCSA, and CVSA regulations. |
|
Synthetic webbing severely degrades at temperatures
above 200°F. |
Low stretch polyester webbing allows for more
secure cargo control. |
|
|
Prolonged exposure to Ultraviolet light adversely
affects nylon and polyester. Tie down straps become
bleached and stiff when exposed to sunlight or
arc
welding. |
All hooks and chain assemblies equal or exceed
strength of webbing |
|
Webbing is soft and comes in varying widths; will not
damage expensive cargo. |
|
|
Many acids, alkalis and chemicals have an adverse
effect on nylon and polyester. |
Large selection - choose the capacity thats right for
the load carried |
|
|
|
|
Safe
Operating Practices |
Light weight, easy to handle |
|
|
|
|
Inspect tie down straps and all hardware when load
is first being secured. |
Large selection of end fastenings, winches and
ratchets make choosing and using the correct
assembly easy |
|
|
Re-tighten tie downs periodically during run. |
|
Never use Load Huggers for anything other than
securing cargo. Do not use for lifting loads or
towing
vehicles. |
Custom lengths available. |
|
|
|
|
Inspection
Criteria |
|
|
|
|
Remove
from service if any of the following are
visible: |
|
|
Load should be securely blocked and stabilized
before tensioning the straps. |
|
|
|
|
|
|
Never exceed rated capacities. |
Cuts, holes, surface abrasion or crushed areas |
|
|
|
|
Use caution when tossing straps and chain anchor
assemblies over a load. |
Burns or chemical damage |
|
|
Separation of load carrying stitch pattern |
|
|
|
|
Check installation of portable winches - ratchet pawl
must be at top of toothed wheel and bolts tight
against
the rub rail. |
Hardware, fittings or tensioning devices which are
broken, bent, twisted, cracked, or have nicks and
gouges |
|
|
|
|
Weld-on winches should not be cracked. |
Knotted webbing |
|
|
|
|
Corner protectors and wear pads should be used to
protect Load Huggers from sharp edges and abrasion. |
Splices or other makeshift repairs |
|
|
The loop ends are damaged. |
|
|
|
|
All hardware must be in line with direction of pull to
achieve full strength. |
|
|
|
Definitions |
|
|
|
|
Working
Load Limit (WLL): The maximum load
that may be applied to an assembly or component in
straight tension. |
|
|
|
Department
of Transportation Regulations 393, 102(b)
use Ultimate Breaking Strength to calculate the number
of tiedown assemblies required to secure a load. |
|
|
|
Ultimate
Breaking Strength: The load at which an
assembly or component will fail in testing. |
|
|
|
|
We
publish Ultimate Strength for this purpose only.
For safety, we recommend that only Working Load
Limits be used for your calculations. |
|
|
|
*CVSA
(Commercial Vehicle Safety Alliance)
www.cvsa.org |
|
|
|
WARNING:
These products may contain chemicals
known to the State of California to cause cancer and/
or birth defects or other reproductive harm. |
|
|
|