Back to Product Page
|
|
|
|
|
|
|
|
|
|
Hi-Viz®
Fluorescent Safety Rings are placed on
the studs of the MaxBullet® hardware to indicate
the top of the door opening in low light conditions. |
|
|
|
|
|
|
|
|
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~
Add items to your online shopping cart ~
Click a Part No. of the item
you wish to purchase.
|
|
|
|
PRICING
|
PART
#
|
DESCRIPTION
|
PRICE
|
|
MaxBullet
Truck Mount Complete Strip Door Kit (8'w x 8'h - 8"
x.198 Low Temp
Scratch-Guard® Strips with 50% Overlap; MaxBullet® Truckmount
Hardware
Kit; Hi-Viz® Fluorescent Safety Rings)
|
$734
|
REPLACEMENT
PARTS
|
|
Refrigerated
Trailer Strip Door Replacement Strips:
(16 - 8" x.198 Low Temp Scratch-Guard® Ribbed Strips,
8' long)
|
$454
|
|
Hi-Viz®
Fluorescent Safety Rings (Package of 10)
|
$4.30
|
|
INSTALLATION |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure
B
|
|
Figure
C
|
Figure
A
|
|
|
|
|
|
|
|
|
Step
3 Measure width of trailer
and, if necessary, cut mounting bar
to length using saw. |
|
|
|
Step
2 Using the self-tapping screws
provided, install L-bracket on stud
as close to roller track as possible
without impeding movement of door
on track. Repeat for other side. |
Step
1 For trailers with roll-up
doors, locate the stud closest to
the door opening in the rear of the
trailer. |
|
|
Step
4 Place mounting bar on
L-brackets and using L-bracket
as a template, mark holes and drill
with a 1/4 drill bit. |
|
|
|
|
|
NOTE:
For trailers with swing
doors, mount bar as close to top of
trailer as possible. Be sure to leave
room for mounting bar and bolts,
approximately 1 from top. |
|
|
|
|
|
|
|
|
|
|
|
NOTE:
Remember to leave
room for mounting bar. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure
D
|
|
Figure
E
|
|
|
Figure
F |
Step
5 Mount bar to L-brackets
using the provided bolts and
locknuts. |
Step
6 Install PVC strips using
preferred amount of overlap. Refer
to diagram on bottom of this
page for details on strip placement |
|
Step
7 Place Hi-Viz safety rings
on bullets where strips overlap
(see Figure F). |
|
|
|
|
|
|
|
|
Step
8 The strips should be trimmed
to leave 1/4 of clearance from the
floor surface. Use a common utility
knife to score and then tear
the strips by hand. |
|
|
|
|
|
|
|
|
|
|
|
STRIP
PLACEMENT GUIDE |
|
|
|
|
|
|
|
PARTIAL
OVERLAP
|
|
FULL
OVERLAP
|
|
|
|
|
|
6
WIDE
MATERIAL |
|
|
|
|
8
WIDE
MATERIAL |
|
|
|
|
12
WIDE
MATERIAL |
|
|
|
MaxBullet, Aleco
Strip Doors, Plastic Strip Door, PVC Strip Door, Strip Door,
Strip Doors, Vinyl Strip Door, Welding Strip, Truck
Mount Strip Door, Insect Barrier, and Traffic Doors from your
source for material handling equipment.
|
Back to Product Page
|