RUBBER STAIR TREAD SYSTEMS

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.

An abrasive mineral coated Grit-Strip is recessed length
of tread at impact area. Meets specs for con- trasting
color to alert Visually Impaired. Flat surface offers long
wear; easy cleaning. Meets Flame Spread Rating of 75
or less using ASTM-E-84 Test. All treads have a sanded
back for better adhesion; contains no asbestos.

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.

Where To Install - Install stair treads on any smooth dry interior step provided the shape of the step conforms to the underneath
contour of the stair tread; particularly at the section where the flat part of the tread joins the nosing. A tight fit between stair treads
and steps is essential. We recommend the use of Epoxy Nose Caulk on all stair tread installations (required with adjust-a-nose treads).

Where Not To Install - If the shape of the steps does not conform to the shape of the stair treads and cannot be altered to
conform, we do not recommend installation of treads unless special instructions are carefully followed. We do not recommend
installing rubber treads on exterior steps.

Room Temperature - Materials, room and adhesives should be no less than 70 degrees Fahrenheit (21 degrees C) 48 hours prior
to, during and after installation.

Repairing Worn and Uneven Edges - Repair worn, uneven, or misaligned edge of steps.
If an open space exists underneath the nosing of the thread when it is applied against the step you must fill the space with Epoxy
Nose Caulk. It is essential that there be no space between the step and the stair tread when the installation is completed.

Preparation for Installation - Surfaces of steps must be level, clean, dry and free from oil, grease, rust, paint, varnish and old
coverings, adhesives and any other foreign substance. Wooden steps should be thoroughly nailed down.
Worn or dished-out steps, cracks, holes, depressions or any other irregularities on the step should be repaired by filling or sealing
and smoothing with an underlayment compound.

Fitting and Cutting - Treads are usually supplied over size, with untrimmed ends, to allow extra material to compensate for variation
in step dimensions.
Treads should be individually trimmed to fit each step, both in depth and from side to side. The rear edge should be cut with a slight
underbevel for a better fit. The stair treads can be marked with an awl and cut using a steel straight edge and a linoleum knife.
The most important factor in proper stair tread installation is to see that no air space exists underneath the nosing part of the treads.
The tread must not flex or move as traffic walks across the steps. Epoxy Nose Caulk should be used as described on the label.
It is important to use the correct adhesive. For vinyl treads, contact adhesive must be used. For rubber treads, install with contact or
suitable rubber flooring adhesive, depending on service conditions. Cove base adhesives are not recommended.

Installation of Rubber Stair Treads - After the steps have been prepared and the stair treads cut and fitted as described,
begin installation by spreading adhesive on the stair step completely covering the surface and the nosing.
When using contact adhesive, the adhesive should then be spread on the bottom of the stair tread and completely underneath the
nosing. Always follow instructions on label of adhesive container.
We suggest coating two steps and two treads at one time, then install the treads as described below. An alternate suggestion is to
apply adhesive to every other step on a flight of stairs, install these treads; go back and do the remainder.

Install Stair Treads - Set the stair tread into its proper position on the step, beginning at the nosing and pushing back firmly and
as tightly as possible, holding up the back surface of the tread. After nosing is completely in place, begin at the front and move back
on the surface of the tread towards the riser; the tread should be pushed down firmly onto the step.
After installation is completed, roll newly installed stair treads with a hand roller, making certain that the stair tread nosing is fitted
tightly against the step nosing. If any difficulty is experienced in holding the nosing to an understair, use a few hardened steel head-
less brads to secure it while the adhesive is drying.
Rubber or vinyl risers should not be installed so as to extend up underneath the nose of the stair tread. The top of the riser should
butt against the bottom of the tread nose.

Final Precautions - Any adhesive or caulking compound on the surface of the stair treads should be wiped off before it dries,
using a cloth dampened in denatured alcohol. If adhesive has dried, remove carefully with #00 steel wool and denatured alcohol. Rub
lightly to avoid dulling and scratching stair treads.
It is important that traffic be kept off the newly installed stair treads, until the adhesive has set up sufficiently to prevent movement
and assure a firm bond.
Where construction work by other trades requires traffic over newly installed stair treads, protect treads with heavy building paper
or planking as needed.
Do not wash or apply any surface treatments for about one week after installation to allow sufficient time for the stair treads to become
tightly bonded to the steps.

Maintenance Tips - The following simple steps for correct care are recommended:
Daily sweeping with soft hair push broom, also before and between washings, will cut down the number of washings and remove
dirt and foreign matter.
During bad weather any accumulated rain or slush should be wiped promptly from stairs to prevent slipping. Wipe up spillage before
it has a chance to harden.
When cleaning is necessary, wipe with cloth or damp mop, using clean room-temperature water. Do not flood stairs.
In stubborn cases, damp mop with room temperature water and solution of liquid detergent suitable for rubber floor covering or a
solution of ammonia and water. Immediately rinse stairs with clean room-temperature water, changing rinsing water frequently.

Rubber Stair Tread Systems, Smooth Flat Surface, Flat Surface Stair Treads, Square (or Curved) Molded Nose, Heavy Duty, Long
Nose, Grit-Strip, Grit-Strip for Visually Impaired, Neoprene Contact Adhesive, and Epoxy Stair Nose Caulk from your complete
source for material handling equipment.