LKG LK Goodwin Co. Material Handling Equipment Toll Free: 1-800-343-2478
HOME ORDER SEARCH QUOTE CONTACT US ABOUT US MY ACCOUNT SHOPPING CART
 
Product Index
 
Back to Product Page

WIRE ROPE HOISTS
SINGLE HOOK MONORAIL HOISTS (4-7.5 TON)

wire rope hoists Wire Rope Hoists are built to last! After 10, 20 and
even 30 years, these hoists are still found abundantly
operating in the field.

Almost All our Wire Rope Hoists are built around a
WORM GEAR Drive, considered to be the heart of
our machine. Worm Gear Drives are rugged and
reliable and offer smooth and quiet operation. The high
ratio worm gear makes the drive inherently self-locking
and thus provides a safe mechanical load brake that
does not require adjustment.

The MAJOR advantage of a Worm Gear HOIST is
its low maintenance. Fewer moving parts have proven
to be the answer to greater dependability and much
fewer repairs.

We offers a wide variety of both standard and custom
hoists that fit almost all applications. Our hoists range
in size from ½ Ton to 15 Ton in capacity. Low Head-
room models start at 11”. Lifts are available in excess
of 100 ft.

Shown With Dual-Head Motorized Trolley
STANDARD FEATURES
OPTIONAL FEATURES
• Capacities: 4 Ton to 7.5 Ton.
• Lifts up to 100 Feet.
• ASME Service Classification: H3 Duty
• Suspensions: Motorized Trolley, Plain Trolley or Lug
   Mount Type.
Worm Gear: Both Hoist & Trolley Drives.
• Hoist Motor is rated 30-Minute Duty (Suitable for VFD
   Operations above 20 HZ).
• Hoist Motor is TENV, Design “D” with Class F Insulation
   and Thermostat.
• Hoist Brake is AC, Magnetic Disc Type (Rated at 150%
   Motor Torque).
• Trolley Motor is TEFC, Continuous Duty with Class B
   Insulation.
• Trolley Speeds: 35 or 60 FPM.
• Primary Voltages: 230 or 460V-3PH-60HZ.
• NEMA 1 Enclosure for Indoor Service.
• Basic Single Speed Controls: Reversing Contactor(s),
   Transformer, Terminal Strip.
• Control Voltage: 115V
• Upper Paddle Limit Switch – Block Actuated.
• Factory Balanced.
• Load Tested At 125% Capacity
• Safety Orange Paint.
• Heavy Duty/High Quality Construction
• Conforms to NFPA 70 (National Electric Code)
• Conforms to OSHA 1910.179 Safety Standards
• Higher Capacities: Up To 15-Ton
• Power Voltage: 208V or 575V-3Ph-60Hz
• Narrow/Hardened Wheels (Patented Track)
• Upgrades for Heavy Service: H4/H4+ Duty
• Heavy Duty Oil Shear Hoist Brake
• 60-Min/Inverter Duty (10:1) Motors
• Class H Insulated Motors
• VFD Control Packages (2-Speeds)
• 2-Speed Motors/Contactor Controls
• Wired Pendants
• Radio Control System/Warning Light
• Mainline Contactor
• Control Voltage: 24V
• NEMA 4/TENV Motors (Outdoor Service)
• UL/CUL Registered Control Panels
• Hoist Gear Type/Trolley Travel Limit Switches
• Slack Cable Limit Switches
• Heavy Duty Rope Guide System
• Deep Grooved Drums (100% Depth Of Cable)
• Overload Devices
• Warning Devices: Flashing Light/Horn
• Trolley Motor Brake
• Collector Brackets
• Pendant Outrigger Arms
• Encoders (For Automated Operation)
• Bumpers: Rubber/Spring
• Synthetic Oil/Heaters (Operation < 10F)
• Anti-Condensation Heaters
• Steel Weather Covers
• Safety Yellow Paint
• High Temperature Features
• Corrosion Resistant Features
• Spark Resistant Features
NOTE: SEE BELOW FOR MORE DETAILS ON
THE OPTIONS AND PRICES.

Standard Feature: Component Parts - Worm Gearing (H & T) Features
HOIST WORM GEARING
HOIST WORM GEAR 3D MODEL
We use Worm Gear Drives on all its Wire Rope Hoists, Drive Tractors and Bridge Crane End Trucks as standard.
Worm Gear Drives are rugged and reliable and offer smooth and quiet operation.

Due to their inherent friction, Worm Gear Drives also act very similar to brakes by retarding motion. For that reason,
brakes are generally NOT required on all our Worm Gear Trolleys, Drive Tractors or End Trucks. Heavy capacity,
high momentum systems operating without VFD controls are sometimes the exception. In these cases, the trolley or
crane may roll more than the acceptable limit without a brake.

For High-Ratio Worm Gear Hoists, there are some major advantages over other hoists.

• High-Ratio Worm Gears safely control the lifting load without the need for a Mechanical Load Brake.
• High-Ratio Worm Gears are inherently Self-Locking thus these hoists are very capable of acting as 2nd
   stopping brake and also holding up a load.
• Worm Gear Hoists have very Low Maintenance as fewer moving parts lead to fewer repairs
• High-Ratio Worm Gear Hoists Conform to CMAA, ASME and OSHA guidelines
DRAWING
single hook monorail hoists

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Price of the item you wish to purchase.


PRICES FOR HOISTS
SINGLE HOOK MONORIAL HOISTS 4 TO 7.5 TON Prices
Model
No.
Cap.
(lbs.)
Speed
(FPM)
Lift
(ft)
Reeving
Type
Cable
(Dia)
Hoist
Motor (HP
@ RPM)
Head
Room
(A)
Wheel
Base
(E)
Hook
Drift
Weight
(lbs)
Motorized
Trolley
(MT)
Plain
Trolle
(PT)
Lug
Mounted
(Blank)
FA8-1010
8,000
10
10
4PS
3/8
5 @ 1200
37"
28 3/4"
2 3/4"
1175
FA8-1017
8,000
10
17
4PS
3/8
5 @ 1200
37"
36 1/4"
4 1/2"
1250
FA8-1024
8,000
10
24
4PS
3/8
5 @ 1200
37"
43 3/4"
6 1/4"
1325
FA8-1031
8,000
10
31
4PS
3/8
5 @ 1200
37"
51 1/4"
7 7/8"
1400
FA8-1517
8,000
15
17
4PS
3/8
7.5 @ 1800
37"
36 1/4"
4 1/2"
1250
FA8-1524
8,000
15
24
4PS
3/8
7.5 @ 1800
37"
43 3/4"
6 1/4"
1325
FA8-1531
8,000
15
31
4PS
3/8
7.5 @ 1800
37"
51 1/4"
7 7/8"
1400
FA8-1539
8,000
15
39
4PS
3/8
7.5 @ 1800
37"
58 3/4"
9 5/8"
1475
FA8-1546
8,000
15
46
4PS
3/8
7.5 @ 1800
37"
66 1/4"
11 1/4"
1550
FA10-1010
10,000
10
10
4PS
3/8
6 @ 1200
37"
28 3/4"
2 3/4"
1200
FA10-1017
10,000
10
17
4PS
3/8
6 @ 1200
37"
36 1/4"
4 1/2"
1275
FA10-1024
10,000
10
24
4PS
3/8
6 @ 1200
37"
43 3/4"
6 1/4"
1350
FA10-1031
10,000
10
31
4PS
3/8
6 @ 1200
37"
51 1/4"
7 7/8"
1425
FA10-1517
10,000
15
17
4PS
3/8
10 @ 1800
37"
36 1/4"
4 1/2"
1275
FA10-1524
10,000
15
24
4PS
3/8
10 @ 1800
37"
43 3/4"
6 1/4"
1350
FA10-1531
10,000
15
31
4PS
3/8
10 @ 1800
37"
51 1/4"
7 7/8"
1425
FA10-1539
10,000
15
39
4PS
3/8
10 @ 1800
37"
58 3/4"
9 5/8"
1500
FA10-1546
10,000
15
46
4PS
3/8
10 @ 1800
37"
66 1/4"
11 1/4"
1575
FA12-1010
12,000
10
10
4PS
7/16
7.5 @ 1200
37"
28 3/4"
2 3/4"
1200
FA12-1017
12,000
10
17
4PS
7/16
7.5 @ 1200
37"
36 1/4"
4 1/2"
1275
FA12-1024
12,000
10
24
4PS
7/16
7.5 @ 1200
37"
43 3/4"
6 1/4"
1350
FA12-1031
12,000
10
31
4PS
7/16
7.5 @ 1200
37"
51 1/4"
7 7/8"
1425
FA12-1517
12,000
15
17
4PS
7/16
10 @ 1800
37"
36 1/4"
4 1/2"
1275
FA12-1524
12,000
15
24
4PS
7/16
10 @ 1800
37"
43 3/4"
6 1/4"
1350
FA12-1531
12,000
15
31
4PS
7/16
10 @ 1800
37"
51 1/4"
7 7/8"
1425
FA12-1539
12,000
15
39
4PS
7/16
10 @ 1800
37"
58 3/4"
9 5/8"
1500
FA15-1019
15,000
10
19
4PS
7/16
7.5 @ 1200
39"
39 1/4"
4 3/4"
1475
FA15-1025
15,000
10
25
4PS
7/16
7.5 @ 1200
39"
46 3/4"
6 3/4"
1550
FA15-1032
15,000
10
32
4PS
7/16
7.5 @ 1200
39"
54 1/4"
8 3/8"
1625
**NOTES**
1. BASIC SINGLE SPEED (NEMA 1) CONTROLS (STANDARD); REV. CONTACTORS, TRANSFORMER & TERMINAL STRIP
2. HOIST MOTOR THERMOSTAT (AS STANDARD)
3. PENDANT AND FURTHER MOTOR/CIRCUIT PROTECTION (ARE OPTIONAL - SEE HOIST ACCESSORIES & OPTIONS)
4. FOR (NO) CONTROLS WITH WIRED J-BOX (NEMA 1) & BALANCED HOIST - SAME PRICE
5. INDOOR OPERATION (AS STANDARD)
6. 230V OR 460V-3PH-60HZ (AS STANDARD)
7. TROLLEYS BUILT TO FIT S-BEAM, W-BEAM OR PATENTED TRACKS (AS STANDARD)
8. FLANGE WIDTH UP TO 7" (AS STANDARD)
9. MOTORIZED TROLLEYS PROVIDED AT 35 OR 60 FPM (AS STANDARD)
10. GEAR TYPE LIMIT SWITCH (AS STANDARD) FOR LIFTS OVER 28 FT (REEVED-4PS) & OVER 40 FT (REEVED-2PS)

Optional Feature: Component Parts -
Control Packages (Hoist, Trolley, Crane)
hoist and trolley controls control panels
Custom Control Panels
Panel With VFD Hoist and Trolley Controls
controls with radio
We offer various Control Packages for all our Hoist and
Crane Equipment. Whether it is Standard or Custom, we
can build the control panel of your choice.

(VFD) Control Packages are slowly becoming very popular
and are almost standard on all new equipment these days.
The benefits of (VFD) Controls by far outweigh its initial
costs. (VFD) Controls allow the operator to precisely and
safely control the load. Acceleration and deceleration rates
and 2-speed control limits are all set to best support the
given application. Any wear induced on mechanical parts
over time when using (VFD) Controls is much less.

Custom Controls With Radio
Please see our photos for further reference on our control panels.

Optional Feature: Component Parts - Overload Limit Switch
overload limit switch
We offer an Overload Limit Switch that is mounted
underneath one of our trolleys as an OPTION. This
Overload Limit Switch can be purchased with a
NEW hoist or for an EXISTING hoist and installed
in the field with minimal effort. This switch is adjusted
within 5% and there is no loss of headroom.

Overload Limit Switch – Trolley Mounted
Optional Feature: Custom Hoists - Rope Guide Hoists
heavy duty rope guide rope guide
Heavy Duty Rope Guide System
Rope Guide Close Up -
Showing Drum and Upper Sheave
We offer a heavy duty Rope Guide System as a SAFETY option on all our NEW Standard Headroom Hoists.

This system features a heavy duty BRONZE Rope Guide and Slide as well as a DEEP GROOVED Drum; grooved
to 100% depth of the wire rope. Our Rope Guide System allows for moderate side pulling, slack cable conditions
and other load swings that may cause the wire rope to lose its proper groove and bind up or pile up on the drum.

This option should ALWAYS be a consideration on LONG LIFT hoist applications but especially on those in which
the operator is not able to clearly see the drum.

Please see our photos for further reference.


Optional Feature: Wire Rope Hoists -
Special Environments - Explosion Proof
explosion proof hoist trolleys with explosion proof motors
Explosion Proof Hoist
Trolleys with Explosion Proof Motors
and Bronze Wheels
explosion proff hoist with spark resistant
explosion proof tractor
Explosion Proof Tractor with Bronze Wheels
Explosion Proof Hoist with Spark Resistant
Features & Overload Limit Switch
explosion proof pendant station
Machines are designed in accordance with our interpretation of the specifications of
the National Electric Code, Underwriters Laboratory and Factory Mutual but are
NOT tested by them, nor do they carry their label as a whole. However, most of the
Individual Electrical Components do carry an Underwriters Laboratory (UL) Label.

Please NOTE; the full responsibility for determining the existence and severity of a
hazard in a specific area rests with the (Authority) responsible for enforcing that code.

Additional NOTES:

• Machines are available for Class I (Vapors): Groups C & D and Class II
   (Dusts): Group E, F & G (As Division 1 or 2)
• We use TENV motors as standard on all Division 2 applications (With
   Contained Hazard) as permitted by NEC code.
• Any requirements for Spark Resistant Features in severe hazardous
   environments lies with the (Authority)
• Spark Resistant Features generally include Stainless Steel Wire Rope,
   Bronze Trolley Wheels and Bronze Hook and/or Complete Block.
Explosion Proof Pendant Station
Please see our photos for further
product and component reference.


Optional Feature: Custom Hoists - Hoists for Corrosive Environments
hoist & tractor stainless steel pendant station
Stainless Steel
Pendant Station
Hoist & Tractor for Corrosive Environment with S.S. Enclosure and Epoxy Finish
This equipment is for use in Corrosive Environments. Outdoor, Marine and Dipping applications are some of the most
typical. Stainless Steel Components and Epoxy Paint are the common features.
Please see our photos for further reference.
Optional Feature: Custom hoists - High Temp/Hot Metal Hoists
extra heavy duty tractor
hot metal hoist
EXTRA HEAVY DUTY TRACTOR WITH
HIGH TEMP FEATURES INCLUDING
STEEL DRIVE WHEEL
HOT METAL HOIST
Dependent upon the severity of the application, we offer many different
features some of which are printed as guidelines by CMAA, ASME
and ASTM publications.
Please see our Equipment Photos as well
as a list of Hot Metal Hoist Features for
further reference.
HOT METAL HOIST FEATURES
• Worm Gear Drive (As 2nd Braking Mechanism).
• Power Circuit Limit Switch.
• Gear Type (Upper & Lower) Limit Switch.
• Wire Rope with IWRC and 8:1 Safety Factor.
• Hoist Frame Mounted Safety Lugs.
• Rotating Light and /or Warning Bell for Trolley Motion.
• Heat/Splatter Shield under Hook Block.
• Heat Shields under Hoist and Trolley Drive Units.
• Class H Insulation for Hoist and Trolley Motors.
• NEMA 12 Enclosures.
• High Temp Internal Wiring.
• High Temp External Wiring with Metal Conduit.
• Magnetic Mainline Contactor.
• Motor Thermostats or Thermal Overload Relays.
• Branch Circuit Fuses.
• NEMA 12 Pendant with Metal Enclosure and Fire
   Sleeve Cord Cover.
• High Temperature Oil in Reducers.
• High Temperature Grease in all Bearings.
• Rubber Bumpers.
• Oversized Hook – Hook Throat Opening and Radius
   shall allow ladle bail to fit firmly in the bowl of the hook.

Optional Feature: Custom Hoists - Hoist and Tractor Combinations
rope guide hoist with tractor drive For superior trolley performance utilize a Hoist &
Tractor Combination.

The consistently POSITIVE action of a drive tractor
will generally out-perform a standard motorized trolley
in many monorail applications.

By combining a drive tractor with your hoist, you will
better negotiate curves, ride up inclines and will eliminate
nuisance slipping in many severe working environments.

Furthermore, the inherent beam tension of a drive tractor
can also serve to RESIST motion in certain applications
particularly when load swing or side-pull present motion
issues.

Rope Guide Hoist with Tractor Drive
Please see our photos for some examples.

twin hook hoist
semi-low headroom hoist
Twin Hook Hoist with Tractor Drive for
Outdoor Use on Curved Monorail
Semi-Low headroom Hoist with Tractor Drive

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Price of the item you wish to purchase.


HOIST ACCESSORIES AND CONTROL OPTIONS PRICES
DESCRIPTION
PRICES
FOR COMPLETE MOTOR & CIRCUIT PROTECTION
Hoist & Trolley B. C. Fuses, TOL'S or T'STATS & Transformer Fuses (P & S)
SELECTIVE MOTOR & CIRCUIT PROTECTION ITEMS
Branch Circuit Fuses - Hoist (or) Trolley (Each Branch)
Thermal Overload Motor Protection (Each Motor)
Motor Thermostat (1/3 HP Motor - Only)
Transformer Fuses - (2) Primary & (1) Secondary
PENDANT - WIRED INTO HOIST CONTROLS WITH UP TO 16 FT OF CHAIN DROP
2-Button Station
4-Button Station
6-Button Station
8-Button Station
CONTROL ACCESSORIES - ITEMIZED
Electronic (Trolley) Soft Start - Up to 4 AMPS (208/230/460V)
Mainline Contactor (15 AMP) - Includes 100VA Transformer
Mainline Contactor (30 AMP) - Includes 100VA Transformer
NEMA 12 Enclosure - (Dust Tight)
NEMA 4 Enclosure - (Water Tight)
Rotary Manual Disconnect (30 AMP)
Gear Type Limit Switch (2-Element)
Gear Type Limit Switch (4-Element)
VARIABLE FREQUENCY DRIVES (VFD) - HOIST
(INCLUDES P.E. DRIVE, FUSE PROTECTION & BRAKE CONTACTOR)
2HP (230/460V)
3HP (230/460V)
4-5HP (230/460V)
6-7HP (230/460V)
10HP (230/460V)
15HP (460V Only)
20HP (460V Only)
INVERTER DUTY - HOIST MOTOR (REQUIRED FOR LOW OPERATING SPEEDS -
VFD SET UNDER 20 HZ)
2HP to 10HP (1800 RPM)
2HP to 6HP (1200 RPM)
7-1/2HP (1200)
VARIABLE FREQUENCY DRIVE (VFD) - TROLLEY (INCLUDES PE DRIVE WITH FUSE PROTECTION)
1HP (230/460V)
2HP (230/460V)
3HP (230/460V)
INVERTER DUTY - TROLLEY MOTOR (REQUIRED FOR LOW OPERATING SPEEDS -
VFD SET UNDER 15 HZ
1/3HP
1/2HP
3/4HP
1HP
1-1/2HP
TENZ MOTOR - TROLLEY (FOR OUTDOOR, WET OR VERY DIRTY ENVIRONMENTS)
1/3HP
1/2HP
3/4HP
1HP
1-1/2HP
BRAKE - TROLLEY
Up to 1/2HP (STD Housing)
Up to 1HP (STD Housing)
Up to 1/2HP (NEMA 4 - Sealed Housing)
Up to 1HP (NEMA 4 - Sealed Housing)
For other options please contact us.
Saturn Wire Rope Hoists, Single Hook Monorail Hoists, Electric Hoists, Powered Wire Rope Hoists, Worm Gear
Trolley, I Beam Hoists, 4-7.5 Ton Trolley Hoist, Worm Gear Hoists, and Electric Wire Rope Hoists from your source
for material handling equipment.

Back to Product Page

HOME / ORDER / SEARCH / QUOTE / CONTACT US / ABOUT US / MY ACCOUNT/ SHOPPING CART