SERIES 4HWF
HELICAL/WORM GEAR POWER WINCHES
		Up to 8,100 lb capacity
		Helical/worm gearing provides rugged reliability suitable    for severe duty applications.
		Standard features include TEFC severe duty brakemotors,    enclosed gearing, flange style roller bearings, and 2-year    limited warranty.
		Custom modifications are also available.
			Please order wire rope and controls separately. (See bottom of page)

WINCH DIMENSIONS
SERIES 4HWF- WINCH DIMENSIONS (in)
Model extension A B C D E H J K L M N P R S (hole dia.) V 4HWF1M-1500-25 25.50 27.00 7.56 8.00 2.38 14.00 1.00 10.00 20.00 22.56 0.62 15.75 17.00 0.59 – 4HWF1M-1500-35 25.50 27.00 7.56 8.00 2.38 14.00 1.00 10.00 20.00 22.56 0.62 15.75 17.00 0.59 – 4HWF2M-2000-25 26.25 28.00 7.56 8.00 2.38 14.00 1.00 10.00 20.00 22.56 0.62 15.75 17.00 0.59 – 4HWF2M-2000-35 26.25 29.75 7.56 8.00 2.38 14.00 1.00 10.00 20.00 22.56 0.62 15.75 17.00 0.59 – 4HWF4M-4000-25 38.75 35.00 11.50 12.00 5.12 21.00 1.00 15.25 30.50 33.38 1.00 24.00 26.00 0.88 – 4HWF4M-4000-35 38.75 35.00 11.50 12.00 5.12 21.00 1.00 15.25 30.50 33.38 1.00 24.00 26.00 0.88 – 4HWF6M-6000-25 40.75 36.00 11.50 12.00 5.12 21.00 1.00 15.25 30.50 33.38 1.00 24.00 26.00 0.88 – 4HWF6M-6000-35 40.75 39.00 11.50 12.00 5.12 21.00 1.00 15.25 30.50 33.38 1.00 24.00 26.00 0.88 – 4HWF8M-8000-25 49.75 43.25 14.50 14.50 6.25 25.50 1.25 13.25 26.50 43.50 1.12 28.75 31.00 1.12 39.75 4HWF8M-8000-35 49.75 45.25 14.50 14.50 6.25 25.50 1.25 13.25 26.50 43.50 1.12 28.75 31.00 1.12 39.75
Dimensions are for reference only and subject to change without notice. Please contact us for exact dimensions.

DRUM DIMENSIONS
Important: It is the owner's or operator's responsibility to determine the suitability of the equipment to its intended use. Study all applicable codes, manuals, and regulations. Be sure to read the Owner's Manual supplied with the equipment before operating it.
SERIES 4HWF - DRUM DIMENSIONS
Series Drum dia. Flange dia. Drum width Fleet angle distance4 4HWF1M 4.50 in 12.00 in 10.00 in 15.9 ft 4HWF2M 5.50 in 12.00 in 10.00 in 15.9 ft 4HWF4M 7.00 in 18.00 in 16.00 in 25.4 ft 4HWF6M 9.00 in 18.00 in 16.00 in 25.4 ft 4HWF8M 10.75 in 22.00 in 20.00 in 31.8 ft
Dimensions are for reference only and subject to change without notice. Please contact us for exact dimensions.
4 Recommended minimum distance between drum and lead sheave for smooth drum.

ELECTRIC MOTOR CONTROLS
		Single Speed Reversing Magnetic Controls for 1 and 3 phase motors up to 40 hp
		UL, IEC, or CSA Recognized components throughout.
		Steel Enclosure NEMA 4 rated (watertight) keeps dirt    and water out. Approved for most outdoor applications.
		Pendant Control Switch NEMA 4X rated (watertight),    on 50 foot cord, allows operator to stand away from winch    during operation. Pendant control is operated with momen-    tary contact-type push buttons. Cord lengths of less than    50 feet are available, please specify when ordering.
		Reversing Contactor is electrically and mechanically    interlocked to deliver smooth reversing control.
When ordering please include the following: voltage and phase required, motor horsepower, pendant control cord length - up to 50 ft., and pendant control labeling - For/Rev or Up/Down.
		Thermal Overload Relay trips power OFF to protect    motor from overheating. Switch is manually reset.
		Fused Control Circuit powers pendant with 115 volt,    2 amp current to help protect against high voltage shocks.
		Wiring Diagram is supplied inside enclosure.
OPTIONS
		Steel Mounting Bracket secures control box to winch.
Special current or horsepower ratings, special rated enclosures for explosive or harsh environments, soft start or soft stop controls, variable speed or multispeed controls, torque limiting controls, selector switches, power cord disconnects, and various panel mounted controls or pilot lights.
		Variable Frequency Drives
		Variable frequency drive controls are available to provide    accurate positioning of loads, soft starts and soft stops, and    overload protection.
		For 3 phase 230 VAC and 460 VAC motors from 1 to 5 hp.
		For 3 phase 230 VAC motors from 1 to 30 hp.
		For 3 phase 460 VAC motors from 1 to 60 hp.

WIRE ROPE
		How to Order Wire Rope
		The breaking strength of new wire rope should be 5 times the size of the largest load for lifting applications, and 3 times the size of the largest load for pulling applications.

Back to Product Page