| SPECIFICATIONS |
|
|
|
|
|
|
|
|
| Construction
Features: |
|
Lifting
Capacity: |
|
|
|
|
|
|
|
|
•
Heavy-duty angle base drilled for six (6) 1/2" bolts
(9/16" mounting holes) with no welding required |
|
•
10% (6°): 10,000 lbs • 60% (31°): 1,900 lbs |
|
•
20% (11°): 5,000 lbs • 80% (39°): 1,600 lbs |
•
Fully sealed aluminum housings, with precision-cut
gears, run in an oil bath |
|
•
40% (22°): 2,600 lbs • 100% (45°): 1,400 lbs |
|
|
|
|
|
|
Our
winch-hoist are rated for what they will vertically lift. Above
data is based on the total load that may be pulled, single line,
up
a given incline. All capacities are reduced 20% to allow for
minimum friction in pull. |
| •
Stress-proof drum shaft |
|
| •
Frictionless bearings |
|
|
|
|
|
| Gear
System: |
|
|
|
|
|
|
|
Cable
Strength: |
|
|
|
|
•
30:1
• Hardened steel worm and forged bronze worm gear
holds load in position when stopped |
|
|
|
|
|
|
|
•
5 to 1 recommended safety factor
• Top-quality galvanized cable available in the following
breaking strengths: |
|
|
|
|
| Power: |
|
|
|
1/8"
- 2,000 lbs
3/16" - 4,200 lbs |
|
1/4"
- 7,000 lbs
5/16" - 9,800 lbs |
|
|
|
|
|
|
| •
High-torque rotary hydraulic motor |
|
|
|
|
|
|
|
|
| •
1/2" - 14 NPTF hydraulic connections |
|
|
|
|
|
|
Dimensions:
(W" x H" x L") |
|
|
|
|
|
|
|
|
9"
x 9" x 21" |
| Pump
Requirements: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•
2 GPM @ 900 psi minimum pump capacity
• 12 GPM @ 1,500 psi recommended pump capacity
• 2,250 maximum psi |
|
Shipping
Weight:
60 lbs |
|
|
|
|
|
|
Factory-Installed
Options: |
|
|
|
|
|
|
•
Clutch
• Alternate Drums
• Hydraulic Rope Winch-Hoist |
|
|
|
|
| Speeds: |
|
|
|
|
|
| Typical
System Operation (12 GPM @ 1,500 psi) |
|
•
17 FPM: No-load drum speed
• 14 FPM: 1,000 lbs - single-line lift
• 10 FPM: 1,500 lbs - double-line lift |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Minimum
System Operation (2 GPM @900 psi) |
|
|
|
|
|
•
5 1/2 FPM: No-load drum speed
• 4 1/2 FPM: 1,500 lbs - single-line lift
• 4 FPM: 1,500 lbs. - double-line lift |
|
|
|
|
|
| Note:
All speeds are based on one layer of cable on drum. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Drum
Cycle: |
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
25% - 15 min/hr when operating at full load |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Drum
Storage: |
|
|
|
|
|
|
|
|
|
|
|
|
|
•
1/8" - 1,000 ft
• 3/16" - 450 ft |
•
1/4" - 250 ft
• 5/16" - 150 ft |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For
best results, use the minimum amount of cable
required for application plus four safety turns around
the drum. Cable sold separately. Length and size must
be specified at time of order. |
|
|
|
|
|
